Catalogue 2 - STAUFF Connect

www.stauff.com/2/en/#197 197 L Swivel Elbow Type FI-DGWE-...-M-WD § Series L / S Ordering Codes * FI-DGWE * -10 * L *M* -WD * -B * -W66 * -MS * Swivel Elbow FI-DGWE * Outside Tube Diameter D1 (in mm) -10 * Series Light Series L Heavy Series S * Thread Type Metric Parallel Thread M If required, please indicate special sizes, e.g. M27x2! * Seal Type Profile Sealing Ring -WD * Seal Material NBR (Buna-N®) -B FKM (Viton®) -V * Material Code Steel, zinc-plated and thick-film-passivated -W66 Please contact STAUFF for alternative materials and surface finishings. * Assembling / Kitting Fitting body only — Fitting body supplied with cutting ring and union nut -MS Fitting body supplied with soft-sealing cutting ring -MSV and union nut Profile Sealing Ring Metric Parallel Thread Series Tube OD PN Dimensions Torque Weight Ordering Codes 3 mm bar mm N·m kgca. D1 T D2 i1 L1 L1 1 L2 L3 L4 S1 S2 S3 Thread T per 100 L 6 250 M 10 x 1 14 8 23,531,516,540 21 27 19 14 18 15,60 FI-DGWE-06LM-WD-B-W66 6 250 M 12 x 1,5 17 12 23,531,516,541 22 27 19 14 25 16,00 FI-DGWE-06LM12x1.5-WD-B-W66 8 250 M 12 x 1,5 17 12 23,531,516,541 22 27 19 17 25 16,80 FI-DGWE-08LM-WD-B-W66 8 250 M 14 x 1,5 19 12 25 33 18 46 25 30 22 17 45 23,30 FI-DGWE-08LM14x1.5-WD-B-W66 10 250 M 14 x 1,5 19 12 26 34 19 46 25 30 22 19 45 23,00 FI-DGWE-10LM-WD-B-W66 10 250 M 16 x 1,5 22 12 27 35 20 48 27 32 24 19 60 24,80 FI-DGWE-10LM16x1.5-WD-B-W66 12 250 M 16 x 1,5 22 12 27 35 20 48 27 32 24 22 60 27,50 FI-DGWE-12LM-WD-B-W66 12 250 M 18 x 1,5 24 12 29 37 22 55 30 36 27 22 100 39,20 FI-DGWE-12LM18x1.5-WD-B-W66 15 250 M 18 x 1,5 24 12 30 38 23 55 30 36 27 27 100 39,00 FI-DGWE-15LM-WD-B-W66 15 250 M 22 x 1,5 27 14 32 40 25 59 33 40 32 27 125 52,50 FI-DGWE-15LM22x1.5-WD-B-W66 18 160 M 22 x 1,5 27 14 32 41 24,559 33 40 32 32 125 53,50 FI-DGWE-18LM-WD-B-W66 22 160 M 26 x 1,5 32 16 36,545,529 66 35 45 36 36 180 70,00 FI-DGWE-22LM-WD-B-W66 28 100 M 33 x 2 40 18 41,551 34 78 41 55 41 41 300 128,00 FI-DGWE-28LM-WD-B-W66 35 100 M 42 x 2 50 20 48,559,538 92 50 65 50 50 450 206,00 FI-DGWE-35LM-WD-B-W66 42 100 M 48 x 2 55 22 53,565,542,5102 56 75 55 60 540 294,00 FI-DGWE-42LM-WD-B-W66 S 6 400 M 12 x 1,5 17 12 25,533,518,541 22 27 19 17 35 17,20 FI-DGWE-06SM-WD-B-W66 8 400 M 14 x 1,5 19 12 25,533,518,541 22 27 19 19 55 18,20 FI-DGWE-08SM-WD-B-W66 10 400 M 16 x 1,5 22 12 27 36 19,546 25 30 22 22 70 23,80 FI-DGWE-10SM-WD-B-W66 12 400 M 18 x 1,5 24 12 28 37 20,548 27 32 24 24 90 28,20 FI-DGWE-12SM-WD-B-W66 14 400 M 20 x 1,5 26 14 32 42 24 55 30 36 27 30 125 45,00 FI-DGWE-14SM-WD-B-W66 16 400 M 22 x 1,5 27 14 34 44 25,559 33 40 32 30 135 53,60 FI-DGWE-16SM-WD-B-W66 20 250 M 27 x 2 32 16 38,549,528 66 35 45 36 36 180 71,50 FI-DGWE-20SM-WD-B-W66 25 250 M 33 x 2 40 18 45,557,533,578 41 55 41 46 310 128,20 FI-DGWE-25SM-WD-B-W66 30 250 M 42 x 2 50 20 52,565,539 92 51 65 50 50 470 210,00 FI-DGWE-30SM-WD-B-W66 38 250 M 48 x 2 55 22 59,574,543,5102 56 75 55 60 800 300,00 FI-DGWE-38SM-WD-B-W66 Spare Parts / Accessories Profile Sealing Ring Type WDG Page 238 Connecting Parts Cutting Ring Type FI-DS Page 28 Soft-Sealing Cutting Ring Type FI-WDDS Page 29 Support Sleeve Type FI-VH Page 31 STAUFF Form EVO Sealing Ring Type FI-FD Page 32 Union Nut Type FI-M Page 33 37° Flared Tube Fitting Set Type FI-AB Page 37 1 Approx.imate dimension in assembled condition. 2 Weight excluding cutting ring and union nut. 3 Standard scope of delivery: Fitting body only. Standard seal material is NBR (Buna-N®). Male stud acc. to ISO 9974-2 (Type E) Port acc. to ISO 9974-1 Torque recommendations for Steel mating material. Dimension S1 (mm) 27 30 32 36 40 45 55 65 75 Revolutions Per Minute 6 3 3 1 0,6 0,5 0,4 0,2 0,2 Maximum Number of Revolutions per Minute for Permanent Operation Higher number of revolutions per minute possible when used temporarily / non-permanently. Recommendations for use with hydraulic oil at a static working pressure not exceeding 200 bar. Catalogue 2 § Edition 03/2024 Swivel Fittings Male threaded studs were designed for female threaded ports in components made of steel. For applications with components made of softer mating materials (e.g. Alumi- nium), the use of connectors with additionally rolled male threads is recommended. Please contact STAUFF prior to the assembly for further information.