Catalogue 10 - STAUFF Hydraulic Accessories

58 www.stauff.com/10/en/#58 D Suction Strainer (Polyamide End Cap) T ype SUS Characteristics Designed as in-tank suction strainer elements for direct installation into suction lines of pumps; should always be installed below the minimum fluid level of the reservoir Features ƒ Available with female BSP thread (ISO 228) or female NPT thread (ANSI B1.20.1) ƒ Operating temperature range: -20°C ... +100 °C / -4°F ... +212 °F Group Size Thread T Dimensions (mm / in) Filter Max. ØD1 ØD2 L Hex Surface Flow Rate 040-G06-075 G3/8 BSP 39,5 38,5 75 22 279cm² 12 l/min 1.56 1.53 2.93 .87 43 in² 3.1USGPM 050-G06-067 G3/8 BSP 50 49 67 26 296cm² 12 l/min 1.97 1.93 2.64 1.02 46 in² 3.1USGPM 050-G08-105 G1/2 BSP 50 49 105 26 518cm² 15 l/min 1.97 1.93 4.13 1.02 80 in² 3.9USGPM 068-G12-105 G3/4 BSP 68 66 105 34 676cm² 25 l/min 2.68 2.60 4.13 1.34 105 in² 6.5USGPM 068-G16-140 G1 BSP 68 66 140 42 930cm² 50 l/min 2.68 2.60 5.51 1.65 144 in² 13.0USGPM 088-G20-140 G1-1/4 BSP 88 85 140 50 1172cm² 65 l/min 3.46 3.35 5.51 1.97 182 in² 16.9USGPM 088-G24-140 G1-1/2 BSP 88 85 140 60 1172cm² 140 l/min 3.46 3.35 5.51 2.36 182 in² 36.4USGPM 102-G24-200 G1-1/2 BSP 102 100 200 72 2427cm² 140 l/min 4.02 3.94 7.87 2.83 376 in² 36.4USGPM 102-G32-200 G2 BSP 102 100 200 72 2427cm² 230 l/min 4.02 3.94 7.87 2.83 376 in² 59.8USGPM 102-G32-225 G2 BSP 102 100 225 72 2811cm² 230 l/min 4.02 3.94 8.86 2.83 436 in² 59.8USGPM 102-G32-260 G2 BSP 102 100 260 72 3249cm² 230 l/min 4.02 3.94 10.24 2.83 504 in² 59.8USGPM 102-G32-300 G2 BSP 102 100 300 72 3798cm² 230 l/min 4.02 3.94 11.81 2.83 589 in² 59.8USGPM 131-G40-191 G2-1/2 BSP 131 128 191 86 2430cm² 340 l/min 5.16 5.04 10.24 3.39 377 in² 88.4USGPM 131-G40-212 G2-1/2 BSP 131 128 212 86 2748cm² 340 l/min 5.16 5.04 8.35 3.39 426 in² 88.4USGPM 131-G48-272 G3 BSP 131 128 272 96 3626cm² 400 l/min 5.16 5.04 10.71 3.78 562 in² 104USGPM 150-G32-151 G2 BSP 150 145 151 70 1812cm² 400 l/min 5.91 5.71 5.94 2.76 281 in² 104USGPM Group Size Thread T Dimensions (mm / in) Filter Max. ØD1 ØD2 L Hex Surface Flow Rate 050-N06-067 3/8 NPT 50 49 67 26 296cm² 12 l/min 1.97 1.93 2.64 1.02 46 in² 3.1USGPM 050-N06-090 3/8 NPT 50 49 90 26 430cm² 12 l/min 1.97 1.93 3.54 1.02 67 in² 3.1USGPM 050-N08-105 1/2 NPT 50 49 105 26 518cm² 15 l/min 1.97 1.93 4.13 1.02 80 in² 3.9USGPM 068-N12-105 3/4 NPT 68 66 105 34 676cm² 25 l/min 2.68 2.60 4.13 1.34 105 in² 6.5USGPM 068-N16-140 1 NPT 68 66 140 42 930cm² 50 l/min 2.68 2.60 5.51 1.65 144 in² 13.0USGPM 088-N20-140 1-1/4 NPT 88 85 140 50 1172cm² 65 l/min 3.46 3.35 5.51 1.97 182 in² 16.9USGPM 088-N20-195 1-1/4 NPT 88 85 195 60 1709cm² 65 l/min 3.46 3.35 7.68 2.36 265 in² 16.9USGPM 088-N24-140 1-1/2 NPT 88 85 140 60 1172cm² 140 l/min 3.46 3.35 5.51 2.36 182 in² 36.4USGPM 088-N24-226 1-1/2 NPT 88 85 226 60 2012cm² 140 l/min 3.46 3.35 8.90 2.36 312 in² 36.4USGPM 088-N24-260 1-1/2 NPT 88 85 260 60 2344cm² 140 l/min 3.46 3.35 10.24 2.36 363 in² 36.4USGPM 102-N24-200 1-1/2 NPT 102 100 200 72 2427cm² 140 l/min 4.02 3.94 7.87 2.83 376 in² 36.4USGPM 102-N32-260 2 NPT 102 100 260 72 3249cm² 230 l/min 4.02 3.94 10.24 2.83 504 in² 59.8USGPM 131-N40-212 2-1/2 NPT 131 128 212 86 2748cm² 340 l/min 5.16 5.04 8.35 3.39 426 in² 88.4USGPM 131-N48-272 3 NPT 131 128 272 96 3626cm² 400 l/min 5.16 5.04 10.71 3.78 562 in² 104USGPM Dimensions and Technical Data (Female BSP Threaded Version) Dimensions and Technical Data (Female NPT Threaded Version) Media Compatibility ƒ Suitable for use with Mineral and Petroleum based hydraulic fluids (HL and HLP) Materials ƒ Threaded end cap made of glass-fibre reinforced Polyamide (PA); see page 59 for version with Aluminium end cap ƒ Lower end cap and support tube made of Steel, zinc-plated ƒ Standard filter material is Stainless Steel Mesh (125μm); alternative micron ratings of 60μm and 250μm on request Contact STAUFF for alternative materials. Options ƒ Integrated bypass valve with an opening pressure of 0,2bar (3PSI) to reduce the risks of high-pressure drops that can be caused by contaminated strainer elements or high-viscosity fluids Special sizes, designs, materials and configurations are available on request. Contact STAUFF for details. Hex ØD1 ØD2 L Thread T w/o Bypass Valve with Bypass Valve Flow Characteristics Nominal Flow Rate vs. Pressure Drop D P The following characteristics are valid for Mineral oils with a mass density of 0,85kg/dm³ and a kinematic viscosity of 30mm²/s (cSt) at +38°C / +100°F. bar .069 .055 .041 .027 .014 0 38 114 190 266 350 450 l/min 10 20 30 40 50 60 70 80 90 100 110 120 US GPM PSI 1.0 .8 .6 .4 .2 3/8 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 Catalogue 10 § Edition 01/2024 Suction Strainers