Catalogue 10 - STAUFF Hydraulic Accessories

www.stauff.com/10/en/#59 D 59 Suction Strainer (Aluminium End Cap) T ype SUS Characteristics Designed as in-tank suction strainer elements for direct installation into suction lines of pumps; should always be installed below the minimum fluid level of the reservoir Features ƒ Available with female NPT thread (ANSI B1.20.1) ƒ Operating temperature range: -20°C ... +100 °C / -4°F ... +212 °F Media Compatibility ƒ Suitable for use with Mineral and Petroleum based hydraulic fluids (HL and HLP) Materials ƒ Threaded end cap made of Aluminium; see page 58 for version with Polyamide (PA) end cap ƒ Lower end cap and support tube made of Steel, zinc-plated ƒ Filter material made of Stainless Steel Mesh (125μm); alternative micron ratings of 60μm and 250μm on request Contact STAUFF for alternative materials. Options ƒ Integrated bypass valve with an opening pressure of 0,2bar (3PSI) to reduce the risks of high-pressure drops that can be caused by contaminated strainer elements or high-viscosity fluids Special sizes, designs, materials and configurations are available on request. Contact STAUFF for details. Group Size Thread T Dimensions (mm / in) Filter Max. ØD1 ØD2 L Hex Surface Flow Rate 050-N06-067 3/8 NPT 50 49 67 26 296cm² 12 l/min 1.97 1.93 2.64 1.02 46 in² 3.1USGPM 050-N06-090 3/8 NPT 50 49 90 26 430cm² 12 l/min 1.97 1.93 3.54 1.02 67 in² 3.1USGPM 050-N08-105 1/2 NPT 50 49 105 26 518cm² 15 l/min 1.97 1.93 4.13 1.02 80 in² 3.9USGPM 068-N12-105 3/4 NPT 68 66 105 34 676cm² 25 l/min 2.68 2.60 4.13 1.34 105 in² 6.5USGPM 068-N16-140 1 NPT 68 66 140 42 930cm² 50 l/min 2.68 2.60 5.51 1.65 144 in² 13.0USGPM 088-N20-140 1-1/4 NPT 88 85 140 50 1172cm² 65 l/min 3.46 3.35 5.51 1.97 182 in² 16.9USGPM 088-N20-195 1-1/4 NPT 88 85 195 60 1709cm² 65 l/min 3.46 3.35 7.68 2.36 265 in² 16.9USGPM 088-N24-140 1-1/2 NPT 88 85 140 60 1172cm² 140 l/min 3.46 3.35 5.51 2.36 182 in² 36.4USGPM 088-N24-226 1-1/2 NPT 88 85 226 60 2012cm² 140 l/min 3.46 3.35 8.90 2.36 312 in² 36.4USGPM 088-N24-260 1-1/2 NPT 88 85 260 60 2344cm² 140 l/min 3.46 3.35 10.24 2.36 363 in² 36.4USGPM 088-N32-260 2 NPT 88 85 260 70 2344cm² 230 l/min 3.46 3.35 10.24 2.76 363 in² 59.8USGPM 150-N40-213 2-1/2 NPT 150 145 213 90 2741cm² 340 l/min 5.91 5.71 8.39 3.54 425 in² 88.4USGPM 150-N48-272 3 NPT 150 145 272 100 3625cm² 400 l/min 5.91 5.71 10.71 3.94 562 in² 104USGPM Dimensions and Technical Data (Female NPT Threaded Version) Hex ØD1 ØD2 L Thread T w/o Bypass Valve with Bypass Valve Order Codes a Type Suction Strainer for direct installation into suction lines of pumps SUS b Group Size Select ‘Group Size’ from corresponding column in dimensional tables The group size is defined by the diameter ØD1 of the threaded end cap, the thread code (Type and size) and the total length of the suction strainer element (e.g. 040-B06F-075). c Filter Material / Micron Rating Stainless Steel Mesh, 125μm (standard option) 125 Stainless Steel Mesh, 60μm 060 Stainless Steel Mesh, 250μm 250 Contact STAUFF for alternative materials / micron ratings. d Material of Threaded End Cap Glass-fibre reinforced Polyamide P Aluminium (for female NPT threaded version only) A e Bypass Option Without bypass valve (standard option) 0 Integrated bypass valve with opening pressure of 0,2bar (3PSI) B0.2 Flow Characteristics Nominal Flow Rate vs. Pressure Drop D P The following characteristics are valid for Mineral oils with a mass density of 0,85kg/dm³ and a kinematic viscosity of 30mm²/s (cSt) at +38°C / +100°F. bar .069 .055 .041 .027 .014 0 38 114 190 266 350 450 l/min 10 20 30 40 50 60 70 80 90 100 110 120 US GPM PSI 1.0 .8 .6 .4 .2 3/8 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 SUS - 088-G24-140 - 125 - P - O Catalogue 10 § Edition 01/2024 Suction Strainers

RkJQdWJsaXNoZXIy ODUyNzU=