59 www.stauff.com Hose Type Indentification Symbols 2SNK 2SN 4SP 4SH 4SP Standard Hose Assembly Hose Connector Standard HAS Hose Type High Tensile Steel reinforced four spiral hose EN 856 4SP. ISO 3862-1 4SP (MSHA) 4SP Hose Size 3/8" hose inside diameter 10 1/2" hose inside diameter 12 5/8" hose inside diameter 16 3/4" hose inside diameter 19 1" hose inside diameter 25 1-1/4" hose inside diameter 31 1-1/2" hose inside diameter 38 2" hose inside diameter 51 Assembly Length The length of the hose in mm measured to DIN 20066 (centres). Any hose longer than 99999 mm is classed as non standard. Maximum 5 digits. Refer to diagram below: Fitting Type 24° Male cone metric external thread defined in L (Light) or in S (Heavy) EN8434-1 ISO17165 CE 24° Female cone O-Ring defined in L (Light) or in S (Heavy) EN8434-1 ISO17165 DKO 60° Male cone BSPP external thread EN8434-6 BS5200 AGR 60° Female cone BSPP nut thread EN8434-6 BS5200 DKR JIC 37° Male UN/ UNF external thread EN ISO 8434-2 SAE J514 AGJ JIC 37° Female cone UN/ UNF nut thread EN ISO8434-2 SAE J514 DKJ Female Flat sealing UN/UNF nut thread SAE J1453 ORS Flange Standard pressure SAE J518 (3000 PSI Series) SFL Flange High pressure SAE J518 (6000 PSI Series) SFS Connection Size 1/4 (BSPP, BSPT, NPT) 7/16 (JIC, UNF) 04 1/2 (JIC, UNF) 05 3/8 (BSPP, BSPT, NPT) 9/16 (JIC, UNF) 06 1/2 (BSPP, BSPT, NPT, SAE) 3/4 (JIC, UNF) 08 5/8 (BSPP, BSPT, NPT) 7/8 (JIC, UNF) 10 3/4 (BSPP, BSPT, NPT, SAE) 1-1/16 (JIC, UNF) 12 1 (BSPP, BSPT, NPT, SAE) 1-5/16 (JIC, UNF) 16 1-1/4 (BSPP, BSPT, NPT, SAE) 1-5/8 (JIC, UNF) 20 1-1/2 (BSPP, BSPT, NPT, SAE) 1-7/8 (JIC, UNF) 24 2 (BSPP, BSPT, NPT, SAE) 2-1/2 (JIC, UNF) 32 Metric Threads (DIN 2353 sizes) For Metric threads which are specified in L or S series, define Series and then size. E.g.L15 L Series: 06, 08, 10, 12, 15, 18, 22, 28, 35, 42. S Series: 06, 08, 10, 12, 14, 16, 20, 25, 30, 38 Metric Threads (non DIN sizes) For Metric threads which are not specified in L or S series, just define the Metric size and not the pitch size. E.g. M16x1.5 = M16 Angle of Fitting Straight Insert (None) 45 Degree Swept Angle Insert A 90 Degree Swept Angle Insert B a b c d e g f Hose assembly length (DIN 20066) L = Hose assembly length Hose Assemblies for Type HOS-4SP Order Codes - Same Fitting Type and Connection Size Basic Material Of End Connections & Ferrules carbon steel 0 Orientation Settings in line (0 degrees) 0 0 45 degree orientation 1 1 90 degree orientation 2 2 135 degree orientation 3 3 180 degree orientation 4 4 225 degree orientation 5 5 270 degree orientation 6 6 315 degree orientation 7 7 Hose Protection no hose protection 0 Spiral Hose Protector (HPR-SHP) 1 Hose Sleeve (HRP-SLE) (MSHA) 4 Hose Strip (HRP-STR) 8 Hose Velcro® Wrap (HRP-HVW) 9 Pressure Testing no testing required 0 Pressure tested to country specific standard. Refer to Appendix. Supplied with certification 1 Air Pressure tested as per customer specification 2 Pressure tested (proof tested) to Mining Design Guidelines MDG41 (Australian standard for Mining Industy - Surface and Undergound) 3 h i k j Ordering CodesHAS- 4SP -12-1500-DKO L15 B-0 0 0 0 a b c d e f g hijk Tolerance +/- 5° 0 0 1 2 3 4 5 6 7 1 2 3 4 5 6 7
RkJQdWJsaXNoZXIy ODU4NjY4