32 www.stauff.com Hose Type Indentification Symbols 2SNK 2SN 4SP 4SH 2SNK 2SN Hose Assemblies for Types HOS-2SNK / HOS-2SN Fitting Type 24° Male cone metric external thread defined in L (Light) or in S (Heavy) EN8434-1 ISO17165 CE 24° Female cone O-Ring defined in L (Light) or in S (Heavy) EN8434-1 ISO17165 DKO 60° Male cone BSPP external thread EN8434-6 BS5200 AGR 60° Female cone BSPP nut thread EN8434-6 BS5200 DKR JIC 37° Male UN/ UNF external thread EN ISO 8434-2 SAE J514 AGJ JIC 37° Female cone UN/ UNF nut thread EN ISO8434-2 SAE J514 DKJ Female Flat sealing UN/UNF nut thread SAE J1453 ORS Flange Standard pressure SAE J518 (3000 PSI Series) SFL Flange High pressure SAE J518 (6000 PSI Series) SFS e Order Codes - Different Fitting Type and Connection Size - Hose End 1 f g Ordering CodesHAS - 2SNK - 25 - 1500 - DKO L22 A / Hose End 2 on next page a b c d e f g Note: Only define the second connection and size if different from the first connection Order of definition of connections If straight connection on both ends: Define in the order of "Fitting Type" list. If the hose assembly has the same Fitting Type on both ends, define the smallest connection first. If straight connection on one end and an angled connection on the other end: Define the straight end connection first. If angled connection on both ends: Define in the order of "Fitting Type" list. If the hose assembly has the same Fitting Type on both ends, define the smallest connection first. If the connections are the same size, define in the order of "Angle of Fitting" list. Connection Size 1/4 (BSPP, BSPT, NPT) 7/16 (JIC, UNF) 04 1/2 (JIC, UNF) 05 3/8 (BSPP, BSPT, NPT) 9/16 (JIC, UNF) 06 1/2 (BSPP, BSPT, NPT, SAE) 3/4 (JIC, UNF) 08 5/8 (BSPP, BSPT, NPT) 7/8 (JIC, UNF) 10 3/4 (BSPP, BSPT, NPT, SAE) 1-1/16 (JIC, UNF) 12 1 (BSPP, BSPT, NPT, SAE) 1-5/16 (JIC, UNF) 16 1-1/4 (BSPP, BSPT, NPT, SAE) 1-5/8 (JIC, UNF) 20 1-1/2 (BSPP, BSPT, NPT, SAE) 1-7/8 (JIC, UNF) 24 2 (BSPP, BSPT, NPT, SAE) 2-1/2 (JIC, UNF) 32 Metric Threads (DIN 2353 sizes) For Metric threads which are specified in L or S series, define Series and then size. E.g.L22 L Series: 06, 08, 10, 12, 15, 18, 22, 28, 35, 42. S Series: 06, 08, 10, 12, 14, 16, 20, 25, 30, 38 Metric Threads (non DIN sizes) For Metric threads which are not specified in L or S series, just define the Metric size and not the pitch size. E.g. M16x1.5 = M16 Angle of Fitting Straight Insert (None) 45 Degree Swept Angle Insert A 90 Degree Swept Angle Insert B HCS-25-CE-25S-M-W3 HCS-25-CE-25S-M-W3 HCS-25-DKO-22L-045-S-OR-B-B-W3 HCS-25-CE-30S-M-W3 HCS-25-SFL-20-045-M-W3 HCS-25-SFL-16-045-M-W3 HOS-2SNK-25 HOS-2SNK-25 HOS-2SNK-25 Standard Hose Assembly Hose Connector Standard HAS Hose Type Two High Tensile Steel Braid which exceeds EN 857 2SC - ISO 11237-1 2SC - SAE 100R16S 2SNK Steel reinforced two wire braid hose with thin cover EN 853 2SN. SAE 1002AT - ISO 1436-1 2SN/2AT 2SN Hose Size 1/2" hose inside diameter 06 3/8" hose inside diameter 10 1/2" hose inside diameter 12 5/8" hose inside diameter 16 3/4" hose inside diameter 19 1" hose inside diameter 25 1-1/4" hose inside diameter 31 1-1/2" hose inside diameter 38 2" hose inside diameter 51 Assembly Length The length of the hose in mm measured to DIN 20066 (centres). Any hose longer than 99999 mm is classed as non standard. Maximum 5 digits. Refer to diagram below: a b c d Hose assembly length (DIN 20066) L = Hose assembly length
RkJQdWJsaXNoZXIy ODU4NjY4