26 www.stauff.com/10/en/#26 B Plastic Dipstick Types DS-1 / 2 / 3 Anti-Splash Feature Integrated Anti-Splash Feature Adjustable Level Indicators Green Red ØD Type D200: 200 (7.87) Type D300: 300 (11.81) Dimensional drawings: All dimensions in mm (in). 3,4 (.13) 8,5 (.33) For all Plastic Filler Breathers (except Type SPB-1 with connection sizes B04 and N04), dipsticks made of Polyamide are available as an option. These dipsticks are available in 2 standard lengths of 200mm / 7.87 in and 300mm / 11.81 in and equipped with 2 adjustable level indicators in green and red colour. A shorter dipstick length can be achieved by simply cutting down the total length according to individual requirements. The markings at 25,4 mm / 1.00 in to assist simply cutting. All dipsticks have an integrated anti-splash feature protecting the SPB from backspilling fluid and avoiding an early breakdown of the air filter element. Optionally a powerful magnet collects metal particles from the oil and gives extra safety for your application. Please note: When choosing a combination of a dipstick and a basket (see below), the dipstick has to be at least 15mm / .59 in shorter than the basket. Special designs and alternative materials available on request. Please contact STAUFF for further details. Connection Code For Type Suitable Dipstick* ØD ( mm / in ) Male BSP Thread (ISO 228) G1/4 B04 SPB-1 Dipstick Option Not Available G3/8 B06 SPB-1/2 DS-1 10 / .39 G1/2 B08 SPB-1/2/3 DS-2 14 / .55 SPBM G3/4 B12 SPB-1/2 DS-3 18 / .71 SMBT-80 DS-1 10 / .39 G1 B16 SPB-3 DS-3 18 / .71 SMBT-80 DS-1 10 / .39 Male NPT Thread (ANSI B1.20.1) 1/4 N04 SPB-1 Dipstick Option Not Available 3/8 N06 SPB-1 DS-1 10 / .39 1/2 N08 SPB-1 DS-2 14 / .55 3/4 N12 SPB-1/2/3 DS-3 18 / .71 SMBT-80 DS-1 10 / .39 1 N16 SPB-3 DS-3 18 / .71 SMBT-80 DS-1 10 / .39 Plastic Basket S080 SPB-4/5 DS-3 18 / .71 S095-P SPB-5 DS-3 18 / .71 S200 SPB-4/5 DS-3 18 / .71 w/o Basket X SPB-4/5 DS-3 18 / .71 SMBB-80 DS-1 10 / .39 * When ordered seperately, please add the length of the dipstick (in mm) to the ordering code (e.g. DS-2-300). Plastic Basket § Types S080 / S095-P / S200 Ø48,5 (Ø1.91) For the Plastic Filler Breathers SPB-4 and SPB-5, different Types of baskets are available as an option. All baskets have a reinforced 0,8 x 3,5mm / .03 x .14 in mesh (800μm) , so that rough dirt particles are filtered out of the medium and a smooth flow into the tank is being ensured. ThePlastic Basket S080 (length of 105mm / 4.13 in) snaps into the breather housing and suitable for the SPB-4 and SPB-5. ThePlastic Basket S095-P (length of 95mm / 3.74 in) is equipped with a six-hole bolt pattern with flange interface similar to DIN 24557, part 2. It is suitable for the SPB-5 / SMBB-80 only and is installed between the breather housing and the reservoir. TheTelescopic Plastic Basket S200 (maximum length of 205mm / 8.07 in) is ideal to further improve the straining ability and oil flow-through and allowing longer dipstick lengths, where reservoir depth allows. It also snaps into the breather housing and is suitable for the SPB-4 and SPB-5. Please note: When choosing a combination of a dipstick (see above) and a basket, the dipstick has to be at least 15mm / .59 in shorter than the basket. Special designs and alternative materials available on request. Please contact STAUFF for further details. Ø41,5 (Ø1.63) Ø41,5 (Ø1.63) Ø29,5(Ø1.16) max.205 (8.07) Plastic Basket S080 (for SPB-4/5) Material: Polypropylene (PP) Plastic Basket S095-P (only for SPB-5 / SMBB-80) Material: Polyamide (PA) Telescopic Plastic Basket S200 (for SPB-4/5) Material: Polypropylene (PP) Six-hole bolt pattern with flange interface according to DIN 24557, part 2 105 (4.13) 95 (3.74) BCD Ø73±0,2 (2.87±.01) Pressurisation Many tank filler breathers of the SPB, SMBB and SMBT series are also available as pressurised versions. Information on the specific valve and pressurization settings that are available by default can be found on the corresponding catalogue pages. When the fluid level inside the reservoir rises, no air is expelled from the reservoir until the pressurisation level is reached. With decreasing fluid level inside the reservoir, the tank pressure drops and it is ensured that air is drawn into the reservoir. Due to less breathing, the service life of a filler breather and the oil can be increased by using the pressurisation feature. It also minimizes foaming and cavitation, and provides additional protection from moisture entering the reservoir which causes erosion and oil degradation. Further Accessories / Options Weld Riser § Type WR Suitable for SPB-5 (See page 39 for details) Side Mount Bracket (Polyamide) § Type ASMB-1 Suitable for SPB-5 (See page 38 for details) Side Mount Bracket (Aluminium) § Type ASMB-2 Suitable for SPB-5 (See page 38 for details) Catalogue 10 § Edition 01/2024 Tank Filler Breathers
RkJQdWJsaXNoZXIy ODUyNzU=